Questions tagged as ['netplan']

Well, title says mostly all. I have a problem with netplan as it is distributed with current 20.04.3 (#102) and even #103 which is in proposed is not good enough. New "ignore-carrier" option which is kind of new seems to fit the bill, but it is not obvious to me how to deploy current neplan.io "main".

Help ?

How can I implement "iface br-mgmt:0" in netplan config file from the ifupdown config file?

auto eth0
iface eth0 inet manual

auto eth0.10
iface eth0.10 inet manual
   vlan-raw-device eth0

auto br-mgmt
iface br-mgmt inet static
bridge_ports eth0.10
address 10.4.4.38
netmask 255.255.252.0
gateway 10.4.4.0

auto br-mgmt:0
iface br-mgmt:0 inet static
    address 10.4.4.11
    netmask 255.255.252.0
 ...

I've just installed ubuntu 20.04 on an arm64 machine. To set the static IP address I searched the web and found https://linuxize.com/post/how-to-configure-static-ip-address-on-ubuntu-20-04/. But my ubuntu server doesn't have /etc/netplan directory. So I figured out I should install netplan first by doing

apt-get install netplan.io  

Then I made file /etc/netplan/01-netcfg.yaml

network:
  version: 2
  r ...

I have configured my VPS to listen to multiple IP addresses (whole subnet, 255 addresses), for example:

network:
  version: 2
  renderer: networkd
  ethernets:
    ens3:
      addresses:
      - 15.16.17.0/32
      - 15.16.17.1/32
      - 15.16.17.2/32
      - etc.

How can i make sure that the inbound address, for example 15.16.17.1 matches the outbound ip 15.16.17.1 ? When i connect to my serv ...

I'm using Ubuntu 20.04, with systemd-networkd and Netplan. I have two physical interfaces (ens3 and ens4) which are configured by DHCP (with reservations, so I always get the same addresses).

Additionally, I have two tunnel devices. These are outside Netplan/networkd control (they're created by Strongswan, but for all intents and purposes they're created manually by running something like ip tunnel add.. ...

I'm struggling to get netplan to work. (I thought I still wanted resolv.conf this does fix DNS but gets re-written on reboot.) Everything appears to be correct but I can't ping.

$ sudo netplan --debug apply
** (generate:14256): DEBUG: 00:38:22.887: Processing input file /etc/netplan/50-cloud-init.yaml..
** (generate:14256): DEBUG: 00:38:22.888: starting new processing pass
** (generate:14256): DEBU ...

I'm trying to use Strongswan to create an Ipsec tunnel on a server with Netplan. Netplan has currently no configuration for the tunnel1 and tunnel2 interfaces that Ipsec brings up when the tunnels are created. This seems (almost) correct to me.

The ipsec services run a script which creates the tunnel[1,2] interfaces (these could possibly called vti[1,2] if needs be). If a tunnel fails, ipsec will "down"  ...

Help me please. 3-rd day trying.

After installing ubuntu server there is no internet connection. ipconfig not installed and no possibility to install it because of internet connection

So. there is 3 interfaces (picture) I`m trying to config netplan

network:
  ethernets:
    enp3s0:
      dhcp4: true
      dhcp6: true
    enp5s0:
      dhcp4: true
  version: 2

But there is no still internet. I tried man ...

I am running Ubuntu server 20.04.3 LTS on a remote Raspberry Pi 4. It is connected through WiFi to a remote router (IP 192.168.1.1), and I had configured networking with netplan. However after some months I decided to change the DNS configuration, i.e. remove my router local DNS and replace it with Cloudflare's DNS. So knowing that the yaml file is very sensitive with spaces, the only change I mad ...

I have a computer running Ubuntu Server 20.04.3 (using netplan for networking), and I am running into an issue where programs that support binding to a network interface continue to use the default route unless I run them as root. For example, when I run a command such curl --interface myinterface ipchecker.example.com rather than binding to myinterface, curl still sends the traffic through the defau ...

I have two physical interfaces in my device: eth0 and eth1

I want to use eth0 to communicate with a raspberry directly connected via ethernet. The raspberry's static IP is 192.168.1.201. The eth1 interface is connected to a normal router (with network 192.168.1.0/24) for internet access.

My netplan configurations is as follows:

network:
  version: 2
  ethernets:
    eth0:
      addresses:
        -  ...

Here is my setup :

 network:
 version: 2
 renderer: NetworkManager
 #renderer: networkd
 ethernets:
  enp2s0:
   dhcp4: yes
   addresses: []
   nameservers:
           addresses: [1.1.1.1, 1.0.0.1]
  enx28ee52061e61:
   dhcp4: yes
   addresses: []

systemd-resolve --status | grep 'DNS Servers' -A2

DNS Servers: 192.168.1.1
                  1.1.1.1
                  1.0.0.1

So every domain is resolved ...

I setup 21.04 arm64 server and installed minecraft bedrock edition 1.17.11.1 server. It's on a pi4/8.

I can access wifi with the 50-cloud-init.yaml. I installed all updates and have the server autostart at boot and its running.

I've been thinkering with the wifi trying to get it to broadcast an id to log into it (about 30 videos and hundreds of pages) no luck. I've rewritten .yaml up the wazoo for  ...

My company distributes software to clients on Ubuntu VMs. Recently we've been updating all client VMs from Ubuntu 16/18 to Ubuntu 20.04.

We've been having an issue where DNS name resolution isn't working on the internal network. It's working outside of the network (we're able to ping external websites), but we're not able to connect to machines on the internal network by DNS name - only by IP add ...

I'm trying to implement a simple internal network (client - router - server) in Ubuntu 21.04 on VirtualBox.

I'm new to Netplan and I have the configuration for Ubuntu previous releases (16.04) with the old /etc/network/interfaces file.

here is the old configurations :

Client :

# The internal interface on neta
auto enp0s8
iface enp0s8 inet static
    address 192.168.1.11
    netmask 255.255.255.0
     ...

I have a local application that will try to connect to MySQL on 172.1.0.1 when it's on production but I want to be able to test it locally.

At this time, changing the source code is not an option, so all I need really is for 172.1.0.1 to map to be routed to localhost (127.0.0.1). Something that will persist through reboots but it's easy to revert.

I've seen some solutions using iptables or ifconfig  ...

I'm having trouble with some routing. I cannot get to 192.168.1.1 Below is the config. I have tried with onlink and without. Not sure what onlink does really. There are a few switches this machine goes through before it would hit the router. is there something i'm missing? ip route show shows that it has added the routes correctly.

Thanks!

Netplan config

network:
  renderer: networkd
  ethernets:
    enp ...

I need to have access to all IPs of an /26 block assigned to my Ubuntu 20.4 server.

Already tried setting the block with netplan, but I only have access to the first IP in it.

I've tried with ip too, but I need to setup each address manually with the command ip addr add <ip> dev <interface> and this is not reliable, imagine setting up an bigger IP block.

What is the proper way of sett ...

I'm trying to configure a new VLAN/Subnet on my Ubuntu 18.04 servers. I'm trying to follow the example here: https://netplan.io/examples/#configuring-source-routing

But when I follow that example, I can SSH into the servers via the br10 interface address. But from there, I can't ssh to the other nodes via either the br10 or br11 interface. Additionally, the Kubernetes cluster running on the Servers can ...

I have this config

network:
  ethernets:
    eno1:
      dhcp4: no
      addresses: [192.168.0.103/24]
      gateway4: 192.168.0.1
      nameservers:
          addresses: [8.8.8.8,8.8.4.4]
  version: 2
  renderer: networkd

Then I do: sudo netplan try and press ENTER And finally I sudo reboot or shutdown and start manually

And when the machine comes back up the ip is always 192.168.0.102

What wo ...

I'm looking for help to configure network on ubuntu core, I changed the netplan config and I manage to connect to both wifi and ethernet at the same time but there's an internet connection only on wifi. When I'm only on wifi internet works correctly but as soon as I plug the ethernet it stops and I can't ping anything. Is there an option to "try" both network interfaces when pinging something or should ...

I need to add a second network with a second gateway to my ubnutu 20.04 server (with netplan). The setting looks like this:

Ubuntu server:

interface: ens18
IP: 192.168.20.2
gateway: 192.168.20.1
netmask: 255.255.255.0

I need to add a second network (192.168.30.2/24) with a second router (192.168.30.1) as gateway to the server. This router has different vpn connections to external networks.

I also  ...

I know that netplan try has the automatic revert, but are there any other differences? Specifically, is it required to run netplan apply after I confirm netplan try ?

Edit: I can access the internet just fine via the same wireless network using other devices

Other solutions I have tried to no avail Internet access only via VPN (Cisco AnyConnect), when VPN off - DNS look-up fails

No internet even though connected to Wifi network

Ubuntu 20.04 Wifi connected, but cannot access internet

Connected to wifi, but no internet [16.04]

connected to wifi but no internet - ubu ...

On Focal ubuntu server, I just want the wifi interface to come up without trying to connect. I take my laptop to several coffee shops so it would not make sense to hard code the values here. Instead, I will use wpa_supplicant.

Right now the interface comes up but it tries to connect to the internet and timesout after 2 minutes. How can I make just the wifi interface come up without trying to conn ...

I am trying to connect my raspberry pi to a wifi that requires an account to login i.e username and password. I have successfully connected the pi to an open wifi that only requires SSID and password but I cannot find the option to add username.

I used the netplan 50-cloud-init.yaml file as bellow with my SSID and password.

What do i need to add to put in my username.

network:
    version: 2
    ethernet ...

First a bit of background on the problem, I'm trying to create a dynamic malware analysis lab so I'm running inetsim on this ubuntu vm and I have a couple of other vm's on the internal network settings of virtualbox.

Now I'm trying to add regular internet connectivity to this machine (the malware is running on the machines connected to this one and not on this one) but it's not working. I can pin ...

I have an Ubuntu server 18.04 and simple netplan configuration (see below):

---
network:
  ethernets:
    ens1:
      dhcp4: false
      addresses:
      - "192.168.99.1/24"
    ens2:
      dhcp4: false
      addresses:
      - "172.20.0.82/23"
      gateway4: "172.20.0.1"
      nameservers:
        addresses:
        - "172.20.0.62"
  renderer: "networkd"
  version: 2

If I run the command: "ip link s ...

I have looked at all the solutions about how to stop/start/reload the network stack when using netplan configurations (without installing NetworkManager or nmcli) and none of them seem to give a complete option of how to restart the network stack.

I tried:

sudo systemctl stop networking; sudo systemctl start networking sudo systemctl restart networking

sudo systemctl restart sytemd-networking

I have a few questions around the latest release of 20.04 and the server builds without a GUI interface. I have like all my other Servers attempted to build a 20.04 Server without a GUI as I prefer to work with the CLI rather than the GUI however this is proving to be very difficult to manage both the Network Connections as well as the VPN tunnels should we need to or want to manage them. Currently I ha ...